.jpg)
2-6 Slot Racks for Assorted 12V Batteries
Keep 12V Tool Batteries Handy. Added fit for RIDGID packs in our new design. Fits Milwaukee M12, Makita BL1013 BL1014, Bosch BAT411 BAT414 and RIDGID.
- Mount with #8 screws
- Ships from-made in Syracuse NY USA
- Message me for production orders
- No Latching. Use right side up
- Holds up to 5 small packs or 3 large and 2 small packs
2-4 Slot Racks for Black & Decker 20V Batteries
- 4 slot wall mount battery pack holder. Fits Black and Decker 20Vmax and clone packs LBXR20, LBXR20B, LBXR20-OPE, LBXR2020, LBXR20, LB20, LBX20, LB2X4020. Not just another battery holder. Designed to make your day easier. Designed for installation:
- Mount with 4 or more #8 x 3/4" or longer screws on 3.5" by 1-1/4" spacing.
- Keyholes for screws. Mark holes. Drill pilots, Start screws, slide rack on. Tighten screws. No fumbling while starting screws into wall thru rack holes.
- Rack is better than loose holders. Pre spaced slots. Pack spacing is set by rack and is just right.
- Faster install. Save the time you would loose while working out how far apart to mount the singles.
- Just 1 install not 4.
- Mount racks side by side. Screw holes will be 3.5" apart from rack to rack.
- Designed for ease of use:
- Pack spacing of 3.5" gives room to hold pack sides during insert and removal.
- Latching slots hold battery securely. Mount them in your work van. Empty that bucket of packs to a wall of beauty.
- Angled slots to present pack and ease handling. Better access to pack latch than flat battery mounts.
- Relief from squeezing fingers between the wall and pack. Find the latch easily.
- Storage cups between packs. Not found with single slot holders. A small but free bonus of this rack design.
- Prefer non-latching? Cut away latch bar (using wire cutters) to convert to non-latching.
- MadebyMitchell.com in Syracuse NY USA using PLADimensions:
- As installed 2.29" vertical, 1.39" deep 2 slot 5.92" wide 3 slot 9.42" wide 4 slot 12.92" wide
- Available as: 4 slot, 3 slot, 2 slot
.jpg)
2-4 Slot Racks for 12V, 20V, 60V DeWalt Batteries
4 slot wall mount battery pack holder. Fits DeWalt 20Vmax and clone packs
Not just another battery holder. Designed to make your day easier.
Designed for installation:
MadebyMitchell.com in Syracuse NY USA using PLADimensions: As installed 2.29" vertical, 1.39" deep2 slot 5.92" wide3 slot 9.42" wide4 slot 12.92" wide
Available as: 4 slot, 3 slot, 2 slot
- Secure Latching Rack holds up to 4 DeWalt 12Vmax 20Vmax or FlexVolt batteries, DCB205 DCB606 DCB120....
- Mount with 4 or more #8 x 3/4" or longer screws on 3.5" by 1-1/4" spacing.
- Keyholes for screws. Mark holes. Drill pilots, Start screws, slide rack on. Tighten screws. No fumbling while starting screws into wall thru rack holes. OR line em up and drive em in.
- Better than loose holders. Pre-spaced slots. Pack spacing is set by rack and is just right.
- Faster install. Save the time you would loose while working out how far apart to mount the singles.
- Mount racks side by side. Screw holes will be 3.5" apart from rack to rack.
- Pack spacing of 3.5" gives room to hold pack sides during insert and removal.
- Latching slots hold battery securely. Mount them in your work van. Empty that bucket of packs to a wall of beauty.
- Angled slots to present pack and ease handling. Better access to pack latch than flat battery mounts.
- Relief from squeezing fingers between the wall and pack. Find the latch easily.
- Storage cups between packs. Not found with single slot holders. A small but free bonus of this rack design.
- Prefer non-latching? Cut away latch bar (using wire cutters) to convert to non-latching.
MadebyMitchell.com in Syracuse NY USA using PLADimensions: As installed 2.29" vertical, 1.39" deep2 slot 5.92" wide3 slot 9.42" wide4 slot 12.92" wide
Available as: 4 slot, 3 slot, 2 slot
